 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| User's Manual IE-789136-NS-EM1 Emulation Board Target Devices PD789104A Subseries PD789124A Subseries PD78F9116B PD789114A Subseries PD789134A Subseries PD78F9136B Document No. U14363EJ2V0UM00 (2nd edition) Date Published July 2002 N CP(K) (c) 1999 1991 Printed in Japan [MEMO] 2 User's Manual U14363EJ2V0UM Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. PC/AT is a trademark of International Business Machines Corporation. * The information in this document is current as of March, 2002. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. * NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. * NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4 User's Manual U14363EJ2V0UM 3 Regional Information Some information contained in this document may vary from country to country. Before using any NEC product in your application, pIease contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: * * * * * Device availability Ordering information Product release schedule Availability of related technical literature Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) Network requirements * In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. NEC Electronics Inc. (U.S.) Santa Clara, California Tel: 408-588-6000 800-366-9782 Fax: 408-588-6130 800-729-9288 * Filiale Italiana Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99 * Branch The Netherlands Eindhoven, The Netherlands Tel: 040-244 58 45 Fax: 040-244 45 80 NEC Electronics Hong Kong Ltd. Hong Kong Tel: 2886-9318 Fax: 2886-9022/9044 NEC Electronics Hong Kong Ltd. Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411 NEC do Brasil S.A. Electron Devices Division Guarulhos-SP, Brasil Tel: 11-6462-6810 Fax: 11-6462-6829 * Branch Sweden Taeby, Sweden Tel: 08-63 80 820 NEC Electronics (Europe) GmbH Fax: 08-63 80 388 Duesseldorf, Germany * United Kingdom Branch Tel: 0211-65 03 01 Milton Keynes, UK Fax: 0211-65 03 327 Tel: 01908-691-133 Fax: 01908-670-290 * Sucursal en Espana Madrid, Spain Tel: 091-504 27 87 Fax: 091-504 28 60 * Succursale Francaise Velizy-Villacoublay, France Tel: 01-30-67 58 00 Fax: 01-30-67 58 99 NEC Electronics Shanghai, Ltd. Shanghai, P.R. China Tel: 021-6841-1138 Fax: 021-6841-1137 NEC Electronics Taiwan Ltd. Taipei, Taiwan Tel: 02-2719-2377 Fax: 02-2719-5951 NEC Electronics Singapore Pte. Ltd. Novena Square, Singapore Tel: 253-8311 Fax: 250-3583 J02.4 4 User's Manual U14363EJ2V0UM Major Revisions in This Edition Pages Throughout * * * * * Description Deletion of NP-28CT from supported emulation probes Addition of IE-78K0S-NS-A as supported in-circuit emulator Addition of NP-H36GS and NP-30MC as supported emulation probe Addition of YQGUIDE as fixing screw Addition of YSPACK30BK and NSPACK30BK as supported conversion adapter pp.12, 13 Figure 1-1 System Configuration * Change of supply medium for debugger ID78K0S-NS to CD-ROM * Change of Notes 1 to 3. Modification of a part of Table 1-1 Basic Specifications 3.2.1 Overview of clock settings * Change from "internal clock" to "clock oscillator" * Addition of VSS pin in (a) Clock oscillator in Figure 3-2 External Circuits Used as System Clock Oscillator * Change from "resonator" to "clock oscillator or external clock" on target system in Figure 3-3 When Using Clock That Is Already Mounted on Emulation Board and Figure 3-4 When Using UserMounted Clock * Change from "clock generator" to "external clock" in Figure 3-5 When Using External Clock Deletion of 3.4 Low-Voltage Emulation Setting. Addition of 3.4 Setting Power Supply Voltage of Target Interface 3.6 Switch and Jumper Settings * Addition of (2) Switch and jumper settings on IE-78K0S-NS-A Addition of APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM p.15 pp.20 to 22 p.29 in 1st edition p.28 p.30 p.36 The mark shows major revised points. User's Manual U14363EJ2V0UM 5 INTRODUCTION Product Overview The IE-789136-NS-EM1 is designed to be used with the IE-78K0S-NS or IE-78K0S-NS-A to debug the following target devices that belong to the 78K/0S Series of 8-bit single-chip microcontrollers. * PD789104A Subseries: PD789101A, 789102A, 789104A * PD789114A Subseries: PD789111A, 789112A, 789114A * PD789124A Subseries: PD789121A, 789122A, 789124A * PD789134A Subseries: PD789131A, 789132A, 789134A * PD78F9116B * PD78F9136B Target Readers This manual is intended for engineers who will use the IE-789136-NS-EM1 with the IE78K0S-NS or IE-78K0S-NS-A to perform system debugging. Engineers who use this manual are expected to be thoroughly familiar with the target device's functions and usage methods and to be knowledgeable about debugging. Organization When using the IE-789136-NS-EM1, refer to not only this manual (supplied with the IE789136-NS-EM1) but also the manual that is supplied with the IE-78K0S-NS or IE78K0S-NS-A. IE-78K0S-NS User's Manual * Basic specifications * System configuration * External interface functions IE-789136-NS-EM1 User's Manual * General * Part names * Installation * Differences between target devices and target interface circuits * Restrictions IE-78K0S-NS-A User's Manual * Basic specifications * System configuration * External interface functions Purpose This manual is intended to give users an understanding of the various debugging functions that can be performed when using the IE-789136-NS-EM1. 6 User's Manual U14363EJ2V0UM Terminology Term Emulation device The meanings of certain terms used in this manual are listed below. Meaning This is a general term that refers to the device in the emulator that is used to emulate the target device. It includes the emulation CPU. This is the CPU block in the emulator that is used to execute user-generated programs. This is the device to be emulated (real chip). This includes the target program and the hardware provided by the user. When defined narrowly, it includes only the hardware. This refers to the combination of the IE-78K0S-NS or IE-78K0S-NS-A and the IE-789136-NS-EM1. Emulation CPU Target device Target system IE system Conventions Data significance: Higher digits on the left and lower digits on the right Note: Caution: Remark: Footnote for item marked with Note in the text Information requiring particular attention Supplementary information Related Documents The related documents (user's manuals) indicated in this publication may include preliminary versions. However, preliminary versions are not marked as such. Document Name Document Number U13549E U15207E This manual U15185E U14643E IE-78K0S-NS IE-78K0S-NS-A IE-789136-NS-EM1 ID78K Series Integrated Debugger Ver. 2.30 or Later Operation (WindowsTM Based) PD789104A, 789114A, 789124A, 789134A Subseries Caution The documents listed above are subject to change without notice. Be sure to use the latest documents when designing. User's Manual U14363EJ2V0UM 7 CONTENTS CHAPTER 1 1.1 1.2 1.3 GENERAL...........................................................................................................................11 System Configuration .................................................................................................................12 Hardware Configuration .............................................................................................................14 Basic Specifications ...................................................................................................................15 PART NAMES....................................................................................................................16 CHAPTER 2 2.1 Parts of Main Unit........................................................................................................................17 INSTALLATION ..................................................................................................................18 CHAPTER 3 3.1 3.2 Connection...................................................................................................................................19 Clock Settings .............................................................................................................................20 3.2.1 3.2.2 Overview of clock settings .............................................................................................................20 System clock settings ....................................................................................................................22 3.3 3.4 3.5 3.6 Mask Option Setting....................................................................................................................27 Setting Power Supply Voltage of Target Interface...................................................................28 External Trigger...........................................................................................................................29 Switch and Jumper Settings ......................................................................................................30 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS...........................................................................31 CHAPTER 4 APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE........................................................35 APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM..........................................................36 8 User's Manual U14363EJ2V0UM LIST OF FIGURES Figure No. 1-1 1-2 2-1 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 4-1 B-1 B-2 B-3 B-4 Title Page System Configuration ........................................................................................................................................12 Basic Hardware Configuration...........................................................................................................................14 IE-789136-NS-EM1 Part Names .......................................................................................................................17 Connection of Emulation Probe.........................................................................................................................19 External Circuits Used as System Clock Oscillator ...........................................................................................20 When Using Clock That Is Already Mounted on Emulation Board ....................................................................21 When Using User-Mounted Clock .....................................................................................................................21 When Using External Clock...............................................................................................................................22 Connections on Parts Board (When Using User-Mounted Clock) .....................................................................23 Crystal Oscillator (When Using User-Mounted Clock).......................................................................................25 Pin Alignment of Crystal Oscillator and Socket .................................................................................................25 Mask Option Setting ..........................................................................................................................................27 Connection of TP1 and Power Supply Voltage of Target System .....................................................................28 External Trigger Input Position ..........................................................................................................................29 Equivalent Circuit from Emulation Circuit ..........................................................................................................33 Distance Between In-Circuit Emulator and Flexible Board (NP-36GS) .............................................................36 Connection Condition of Target System (NP-H36GS).......................................................................................37 Distance Between In-Circuit Emulator and Conversion Adapter (NP-30MC) ....................................................38 Connection Condition of Target System (NP-30MC).........................................................................................39 User's Manual U14363EJ2V0UM 9 LIST OF TABLES Table No. 1-1 3-1 3-2 3-3 3-4 3-5 A-1 Title Page Basic Specifications.......................................................................................................................................... 15 System Clock Settings...................................................................................................................................... 22 DIP Switch Setting ............................................................................................................................................ 27 Switch and Jumper Settings on IE-78K0S-NS.................................................................................................. 30 Switch and Jumper Settings on IE-78K0S-NS-A .............................................................................................. 30 Initial Setting of Jumper on IE-789136-NS-EM1 ............................................................................................... 30 NGS-30, NP-36GS, NP-H36GS, and NP-30MC Pin Assignments ................................................................... 35 10 User's Manual U14363EJ2V0UM CHAPTER 1 GENERAL The IE-789136-NS-EM1 is a development tool for efficient debugging of hardware or software when using one of the following target devices that belong to the 78K/0S Series of 8-bit single-chip microcontrollers. This chapter describes the IE-789136-NS-EM1's system configuration and basic specifications. * Target device * PD789104A Subseries * PD789114A Subseries * PD789124A Subseries * PD789134A Subseries * PD78F9116B * PD78F9136B User's Manual U14363EJ2V0UM 11 CHAPTER 1 GENERAL 1.1 System Configuration Figure 1-1 illustrates the IE-789136-NS-EM1's system configuration. Figure 1-1. System Configuration Debugger ID78K0S-NS (sold separately) Device fileNote 1 (available separately) Control software Host machine PC-9800 series or IBM PC/AT TM or compatibles Interface board IE-70000-98-IF-C (sold separately) Interface board IE-70000-PC-IF-C (sold separately) Interface board IE-70000-PCI-IF-A (sold separately) Interface card or Interface cable Interface cable (NS IF Cable) IE-78K0S-NS or IE-78K0S-NS-A (sold separately) NS CARD Cable MC CARD Cable In-circuit emulator IE-70000-CD-IF-A (sold separately) FG Cable IE-789136-NS-EM1 (This product) AC adapter IE-70000-MC-PS-B (sold separately) Emulation probe Note 2 (sold separately) Flexible boardNote 3 (sold separately) Conversion adapterNote 3 (sold separately) Fixing screwNote 3 (sold separately) 12 User's Manual U14363EJ2V0UM CHAPTER 1 GENERAL Notes 1. The device file is as follows, in accordance with the subseries. SxxxxDF789134: PD789104A, 789114A, 789124A, 789134A Subseries, PD78F9116B, 78F9136B The device file can be downloaded from the NEC Electron Devices Web site (URL: http//www.ic.nec.jp/micro). 2. The emulation probes are as follows, in accordance with the package. NP-36GS: For 30-pin plastic shrink SOP (GS type) NP-H36GS: Long type for 30-pin plastic shrink SOP (GS type) NP-30MC: For 30-pin plastic SSOP (MC type) 3. The flexible board, conversion adapter, and fixing screw are as follows. NGS-30: 30-pin plastic shrink SOP (GS type) YSPACK30BK: For 30-pin plastic SSOP (MC type) NSPACK30BK: For 30-pin plastic SSOP (MC type) YQGUIDE: Fixing screw for YSPACK30BK and NSPACK30BK The NP-36GS, NP-H36GS, NGS-30, and NP-30MC are products of Naito Densei Machida Mfg. Co., Ltd. For further information, contact Naito Densei Machida Mfg. Co., Ltd. (TEL: +81-45-475-4191) The YSPACK30BK, NSPACK30BK, and YQGUIDE are products of TOKYO ELETECH CORPORATION. For further information, contact Daimaru Kogyo Co., Ltd. Tokyo Electronics Department (TEL: +81-3-3820-7112) Osaka Electronics Department (TEL: +81-6-6244-6672) User's Manual U14363EJ2V0UM 13 CHAPTER 1 GENERAL 1.2 Hardware Configuration Figure 1-2 shows the IE-789136-NS-EM1's position in the basic hardware configuration. Figure 1-2. Basic Hardware Configuration Dedicated bus interface IE system IE-78K0S-NS (sold separately)/ IE-78K0S-NS-A (sold separately) Host machine Interface board (sold separately) 78K0S main board IE-789136-NS-EM1 Emulation board (this product) Interface card (sold separately) Emulation probe (sold separately) 14 User's Manual U14363EJ2V0UM CHAPTER 1 GENERAL 1.3 Basic Specifications The IE-789136-NS-EM1's basic specifications are listed in Table 1-1. Table 1-1. Basic Specifications Parameter Target device System clock Clock supply Description PD789136 Subseries 1.0 to 10.0 MHz External: Clock input from the target system via an emulation probe Internal: Clock mounted on emulation board (5.0 MHz), or clock mounted on the parts board by the user VDD = 1.8 to 5.5 V (same as target device) The IE-789136-NS-EM1 operates on the internal power supply (5 V) when not connected to the target system. Target interface User's Manual U14363EJ2V0UM 15 CHAPTER 2 PART NAMES This chapter introduces the parts of the IE-789136-NS-EM1 main unit. The packing box contains the emulation board (IE-789136-NS-EM1), packing list, user's manual, and guarantee card. If there are any missing or damaged items, please contact an NEC sales representative. Fill out and return the guarantee card that comes with the main unit. 16 User's Manual U14363EJ2V0UM CHAPTER 2 PART NAMES 2.1 Parts of Main Unit Figure 2-1. IE-789136-NS-EM1 Part Names TP1 GND TP1 Low Volt EXTOUT System clock X1 X1 EXTIN SW1 SW1 G-789136 EM1 board CN2 36GS CN1 28CT Probe connector CN2 36GS/30MC IC7 LED1 IC6 User's Manual U14363EJ2V0UM 17 CHAPTER 3 INSTALLATION This chapter describes methods for connecting the IE-789136-NS-EM1 to the IE-78K0S-NS or IE-78K0S-NS-A, emulation probe, etc. Mode setting methods are also described. Caution Connecting or removing components to or from the target system, or making switch or other setting changes must be carried out after the power supply to both the IE system and the target system has been switched OFF. 18 User's Manual U14363EJ2V0UM CHAPTER 3 INSTALLATION 3.1 Connection (1) Connection with IE-78K0S-NS or IE-78K0S-NS-A main unit See the IE-78K0S-NS User's Manual (U13549E) to the IE-78K0S-NS. Note When using the IE-78K0S-NS-A, refer to the IE-78K0S-NS-A User's Manual (U15207E). (2) Connection with emulation probe See the IE-78K0S-NS User's Manual (U13549E) the IE-789136-NS-EM1. On this board, connect an emulation probe to CN2. Note When using the IE-78K0S-NS-A, refer to the IE-78K0S-NS-A User's Manual (U15207E). Caution Incorrect connection may damage the IE system. Be sure to read the emulation probe's user's manual for a detailed description of the connection method. Figure 3-1. Connection of Emulation Probe Note Note for a description of how to connect the IE-789136-NS-EM1 for a description of how to connect an emulation probe to Emulation probe (sold separately) CN1 (not used) CN2 36GS/30MC IE-789136-NS-EM1 Main board (IE-78K0S-NS or IE-78K0S-NS-A) User's Manual U14363EJ2V0UM 19 CHAPTER 3 INSTALLATION 3.2 Clock Settings 3.2.1 Overview of clock settings The system clock to be used during debugging can be selected from (1) to (3) below. (1) Clock that is already mounted on emulation board (2) Clock that is mounted by user (3) Pulse input from target system If the target system includes a clock oscillator, select either (1) Clock that is already mounted on emulation board or (2) Clock that is mounted by user. For a clock oscillator, a resonator is connected to the target device and the target device's internal oscillator is used. An example of the external circuit is shown in part (a) of Figure 3-2. During emulation, the oscillator that is mounted on the target system is not used. Instead, the clock that is mounted on the emulation board that is installed for the IE-78K0S-NS or IE-78K0S-NS-A is used. If the target system includes an external clock, select (3) Pulse input from target system. For an external clock, a clock signal is supplied from outside of the target device and the target device's internal oscillator is not used. An example of the external circuit is shown in part (b) of Figure 3-2. Caution The IE system will be hung-up if the system clock is not supplied normally. Moreover, be sure to input a rectangular wave as the clock from the target. There is no need to supply a clock to X2 pin. Figure 3-2. External Circuits Used as System Clock Oscillator (a) Clock oscillator Target device Target device VSS X1 External clock X1 (b) External clock X2 X2 20 User's Manual U14363EJ2V0UM CHAPTER 3 INSTALLATION (1) Clock that is already mounted on emulation board A crystal oscillator (X1) is already mounted on the emulation board. Its frequency is 5.0 MHz. Figure 3-3. When Using Clock That Is Already Mounted on Emulation Board IE-78K0S-NS or IE-78K0S-NS-A IE-789136-NS-EM1 Mounted oscillator (to be used) Target system Emulation probe Clock oscillator or external clock (not used) Remark The clock that is supplied by the IE-789136-NS-EM1's oscillator (encircled in the figure) is used. (2) Clock that is mounted by user The user is able to mount any clock supported by the set specifications on the IE-789136-NS-EM1. Remove the crystal oscillator (X1) that is already mounted on the emulation board, and mount either the parts board on which the resonator to be used is mounted or an oscillator. This method is useful when using a different frequency from that of the premounted clock. Figure 3-4. When Using User-Mounted Clock IE-78K0S-NS or IE-78K0S-NS-A IE-789136-NS-EM1 Target system Parts board + resonator or oscillator Emulation probe Clock oscillator or external clock (not used) Remark The clock that is supplied by the parts board with a resonator or oscillator on the IE-789136NS-EM1 (encircled in the figure) is used. User's Manual U14363EJ2V0UM 21 CHAPTER 3 INSTALLATION (3) Pulse input from target system An external clock connected to the target system can be used via an emulation probe. Figure 3-5. When Using External Clock IE-78K0S-NS or IE-78K0S-NS-A IE-789136-NS-EM1 Target system Emulation probe External clock (to be used) Remark The clock supplied by the target system's external clock (encircled in the figure) is used. 3.2.2 System clock settings Table 3-1. System Clock Settings Frequency of System Clock IE-789136-NS-EM1 X1 Socket When using clock that is already mounted on emulation board When using clock mounted by user When pulse is input from target system 5.0 MHz Oscillator used CPU Clock Source Selection (ID) Internal Other than 5.0 MHz Oscillator assembled by user Oscillator not used External Caution When a pulse is input from the target system, open the configuration dialog box when starting the integrated debugger (ID78K0S-NS) and select "External" in the area (Clock) for selecting the CPU's clock source (this selects the user clock). Remark The IE-789136-NS-EM1 is shipped, the settings for "when using clock that is already mounted on emulation board" are preset. (1) When using clock that is already mounted on emulation board When the IE-789136-NS-EM1 is shipped, a 5.0 MHz crystal oscillator is already mounted in the IE-789136-NSEM1's X1 socket. When using the factory-set mode settings, there is no need to make any other hardware settings. When starting the integrated debugger (ID78K0S-NS), open the configuration dialog box and select "Internal" in the area (Clock) for selecting the CPU's clock source (this selects the emulator's internal clock). 22 User's Manual U14363EJ2V0UM CHAPTER 3 INSTALLATION (2) When using clock mounted by user The settings described under either (a) or (b) are required, depending on the type of clock to be used. When starting the integrated debugger (ID78K0S-NS), open the configuration dialog box and select "Internal" in the area (Clock) for selecting the CPU's clock source (this selects the emulator's internal clock). (a) When using a ceramic resonator or crystal resonator * Items to be prepared * Parts board * Ceramic resonator or crystal resonator * Resistor Rx * Capacitor CA * Capacitor CB * Solder kit Pin No. 2-13 3-12 4-11 5-10 8-9 Capacitor CA Capacitor CB Ceramic resonator or crystal resonator Resistor Rx Shorted Connection 1 2 3 4 5 6 7 14 13 12 11 10 9 8 Circuit diagram 1 M HCU04 HCU04 5 Rx 10 4 3 CB 12 11 13 CA 2 98 CLOCK OUT Remark The sections enclosed in broken lines indicate parts that are attached to the parts board. User's Manual U14363EJ2V0UM 23 CHAPTER 3 INSTALLATION <2> Prepare the IE-789136-NS-EM1. <3> Remove the crystal oscillator that is mounted in the IE-789136-NS-EM1's X1 socket. <4> Connect the parts board (from <1> above) to the X1 socket from which the crystal oscillator was removed. Check the pin 1 mark to make sure the board is mounted in the correct direction. <5> Make sure that the parts board is wired as shown in Figure 3-6 above. <6> Install the IE-789136-NS-EM1 in the IE-78K0S-NS or IE-78K0S-NS-A. The above steps configure the following circuit and enable supply of the clock from the mounted resonator to the emulation device. IE-78K0S-NS or IE-78K0S-NS-A side (Emulation device) 1 M 6 HCU04 HCU04 5 Rx X 4 3 CB 12 11 13 CA 2 10 1 M HSK120 100 X1 X1 9 8 LVCC PD789009 HC157 PD789009 Remark The sections enclosed in broken lines indicate parts that are attached to the parts board. 24 User's Manual U14363EJ2V0UM CHAPTER 3 INSTALLATION (b) When using a crystal oscillator * Items to be prepared * Crystal oscillator (see pinouts shown in Figure 3-7) Figure 3-7. Crystal Oscillator (When Using User-Mounted Clock) NC VCC GND CLOCK OUT Crystal oscillator NC VCC 1 2 3 4 5 6 GND CLOCK OUT 7 Socket 14 13 12 11 10 9 8 Crystal Oscillator Pin Name NC GND CLOCK OUT VCC Socket Pin No. 1 7 8 14 <4> Install the IE-789136-NS-EM1 in the IE-78K0S-NS or IE-78K0S-NS-A. User's Manual U14363EJ2V0UM 25 CHAPTER 3 INSTALLATION The above steps configure the following circuit and enable supply of the clock from the mounted resonator to the emulation device. VCC IE-78K0S-NS or IE-78K0S-NS-A side (Emulation device) Crystal oscillator LVCC 100 X1 1 M HSK120 X1 PD789009 HC157 PD789009 (3) When pulse is input from target system No hardware settings are required for this situation. When starting the integrated debugger (ID78K0S-NS), open the configuration dialog box and select "External" in the area (Clock) for selecting the CPU's clock source (this selects the user's clock). 26 User's Manual U14363EJ2V0UM CHAPTER 3 INSTALLATION 3.3 Mask Option Setting By setting the DIP switch (SW1) in the IE-789136-NS-EM1, the 33 k pull-up resistor can be connected to P50 to P53 by mask option. The DIP switch setting is as follows. Table 3-2. DIP Switch Setting SW1 1 Destination pin P50 2 P51 3 P52 4 P53 When the DIP switch is ON, the corresponding pin is pulled-up by the target VDD pin. When it is OFF, the corresponding pull-up resistor is disconnected. Set the DIP switch to OFF for ports that do not exist. Figure 3-9. Mask Option Setting Target VDD 33 k Emulation CPU P50 P51 P52 P53 100 1 M Probe P50 P51 P52 P53 P50 P51 P52 P53 ON 1 2 3 4 Initial setting is OFF OFF 1 O F F SW1 4 User's Manual U14363EJ2V0UM 27 CHAPTER 3 INSTALLATION 3.4 Setting Power Supply Voltage of Target Interface In the IE system, emulation is possible with a voltage of the same level as the power supply voltage of the target system. When the target system is not connected, the IE system automatically operates with the emulator's internal power supply (5 V). When debugging with a voltage that is the same level as that of the target system, supply the same voltage as that of the target system to the TP1 terminal pin of the IE-789136-NS-EM1 (the same applies when the voltage is 5 V). Set the target voltage to between 1.8 and 5.0 V. * Maximum current consumption of TP1 1.8 to 5.0 V: Approximately 100 mA Figure 3-10. Connection of TP1 and Power Supply Voltage of Target System X1 IC6 IC7 SW1 CN2 36GS LED1 Low Volt TP1 GND Emulation probe Target system VDD GND Power supply voltage of target system Caution Connect TP1 on the board and the power supply voltage of the target system after turning off the power of the IE-78K0S-NS or IE-78K0S-NS-A. Remark The VDD pin of the target system is only used for controlling LED1 (TVCC), which monitors whether the power supply of the target system is connected in the IE-789136-NS-EM1. 28 User's Manual U14363EJ2V0UM CHAPTER 3 INSTALLATION 3.5 External Trigger To set up an external trigger, connect it to the IE-789136-NS-EM1's check pins EXTOUT and EXTIN as shown below. See the IE-78K0S-NS User's Manual (U13549E) or IE-78K0S-NS-A User's Manual (U15207E) for pin characteristics, and the ID78K Series Integrated Debugger Ver. 2.30 or Later Operation (Windows Based) (U15185E) for the usage methods. (1) EXTOUT Outputs a low level from the EXTOUT pin on the IE-789136-NS-EM1 for 1.3 s upon the occurrence of a break event. Caution (2) EXTIN An event signal can be input from the EXTIN pin on the IE-789136-NS-EM1. Input a high-level pulse signal for 2 CPU operation clocks or more. Figure 3-11. External Trigger Input Position Connect a pull-up resistor on the target system since this is an open-drain output. X1 IC6 IC7 SW1 CN2 36GS TP1 CN1 28CT LED1 EXTOUT External trigger EXTIN User's Manual U14363EJ2V0UM 29 CHAPTER 3 INSTALLATION 3.6 Switch and Jumper Settings (1) Switch and jumper settings on the IE-78K0S-NS When using the IE-789136-NS-EM1, set the switches and jumpers on the IE-78K0S-NS as shown in Table 3-3. For details of these switch and jumper settings, refer to the IE-78K0S-NS User's Manual (U13549E). Table 3-3. Switch and Jumper Settings on IE-78K0S-NS SW1 Setting OFF SW3 All switches ON SW4 All switches ON JP1 2 to 3 shorted JP4 1 to 2 shorted Caution If the jumpers and switches are set incorrectly, the board may be damaged. (2) Switch and jumper setting on IE-78K0S-NS-A When using the IE-789136-NS-EM1, set the switches and jumpers on the IE-78K0S-NS-A as shown in Table 3-4. For the position of the switches and jumpers, refer to the IE-78K0S-NS-A User's Manual (U15207E). Table 3-4. Switch and Jumper Settings on IE-78K0S-NS-A SW1 Setting OFF JP1 1-2 JP3 Shorted (fixed) Caution If the jumpers and switches are set incorrectly, the board may be damaged. (3) Switch setting on the IE-789136-NS-EM1 The initial setting of the switch on the IE-789136-NS-EM1 is as shown in Table 3-5. For details, refer to 3.2 Clock Settings. Table 3-5. Initial Setting of Jumper on IE-789136-NS-EM1 SW1 Setting All switches OFF 30 User's Manual U14363EJ2V0UM CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS This chapter describes differences between the target device's signal lines and the signal lines of the IE-789136NS-EM1's target interface circuit. Although the target device is a CMOS circuit, the IE-789136-NS-EM1's target interface circuit consists of an emulation CPU, TTL, CMOS-IC, and other emulation circuits. When the IE system is connected with the target system for debugging, the IE system performs emulation so as to operate as the actual target device would operate in the target system. However, some minor differences exist since the operations are performed via the IE system's emulation. (1) Signals input to or output from the EVA chip and the peripheral EVA chip (2) Signals input from the target system via a gate (3) Analog signals (4) Other signals The IE-789136-NS-EM1's circuit is used as follows for signals listed in (1) to (4) above. (1) Signals input to or output from the EVA chip and peripheral EVA chip The following signals perform the same operations as in the PD789104A, 789114A, 789124A, 789134A Subseries, PD78F9116B, and 78F9136B. However, a 1 M pull-down resistor and 100 resistor are inserted in series. * Signals related to port 0 * Signals related to port 1 * Signals related to port 2 * Signals related to port 5 (2) Signals input from the target system via a gate Since the following signals are input via a gate, their timing shows a delay compared to the PD789104A, 789114A, 789124A, 789134A Subseries, PD78F9116B, and 78F9136B. * RESET signal * Signals related to X1 User's Manual U14363EJ2V0UM 31 CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS (3) Analog signals Because the following signals input/output analog-related signals, special processing is not performed in the IE789136-NS-EM1. * AVDD pin * Signals related to port 6 (4) Other signals * VDD pin The emulation CPU operates on the internal power supply (5 V) of the IE-789136-NS-EM1 when not connected to the target system, and operates on the voltage supplied from the voltage supply pin (TP1) when connected to the target system. The VDD pin of the target system is used only to control the LED (TVCC) that indicates whether the target system's power is on or off. * VSS and AVSS pins The VSS and AVSS pins are connected to GND in the IE-789136-NS-EM1. * TEST/VPP pin The TEST/VPP pin is not used in the IE-789136-NS-EM1. * X2 pin The X2 pin is not used in the IE-789136-NS-EM1. 32 User's Manual U14363EJ2V0UM CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS Figure 4-1. Equivalent Circuit from Emulation Circuit (1/2) Probe side 100 Port 0 1 M IE-789136-NS-EM1 side Port 0 Port 1 Port 2 100 LVCC 1 M 33 k Port 1 Port 2 100 Port 5 1 M LVCC HC4066 100 RESET SW1 Port 5 4.7 k RESET X1 LVCC 100 X1 1 M HC157 X1 PD789009 PD789009 HSK120 AVDD Port 6 AVDD Port 6 User's Manual U14363EJ2V0UM 33 CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS Figure 4-1. Equivalent Circuit from Emulation Circuit (2/2) Probe side IE-789136-NS-EM1 side G6H-2F (Relay) Power detection Filter VDD (TP1 Low Volt) 22 F 1 M 100 PC393 X2 OPEN VSS AVSS Emulation device LVCC TEST/VPP OPEN TEST/VPP 34 User's Manual U14363EJ2V0UM APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE Table A-1. NGS-30, NP-36GS, NP-H36GS, and NP-30MC Pin Assignments NGS-30 NP-30MC Emulation Device Side 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 NP-36GS NP-H36GS CN5 Pin No. CN2 Pin No. NGS-30 NP-30MC Emulation Device Side 58 56 49 55 19 18 22 62 65 66 92 91 98 97 21 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 NP-36GS NP-H36GS CN5 Pin No. CN2 Pin No. 19 20 21 22 23 24 25 33 32 31 30 29 28 27 26 11 10 9 8 7 6 5 4 12 13 14 15 16 17 18 99 63 64 70 69 72 102 71 94 93 30 29 24 23 20 Remarks 1. The NGS-30, NP-36GS, NP-H36GS, and NP-30MC are products of Naito Densei Machida Mfg. Co., Ltd. 2. The numbers in the "NGS-30 Emulation Device Side" column indicate the corresponding pin number on the target system side tip of the NGS-30 and NP-30MC. 3. The numbers in the "NP-36GS, NP-H36GS CN5 Pin No." column indicate the pin number of the NP36GS and NP-H36GS connectors connected to the NGS-30 side. User's Manual U14363EJ2V0UM 35 APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM Figures B-1 to B-4 show the conditions when connecting the emulation probe to the flexible board and the conversion adapter. Follow the configuration below and consider the shape of parts to be mounted on the target system when designing a system. Figure B-1. Distance Between In-Circuit Emulator and Flexible Board (NP-36GS) In-circuit emulator IE-78K0S-NS or IE-78K0S-NS-A Target system Emulation board IE-789136-NS-EM1 155 mmNote CN2 Emulation probe NP-36GS Flexible board NGS-30 Note Distance when NP-36GS is used. When NP-H36GS is used, the distance is 355 mm. Remark NP-36GS, NP-H36GS, and NGS-30 are products of Naito Densei Machida Mfg. Co., Ltd. 36 User's Manual U14363EJ2V0UM APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM Figure B-2. Connection Condition of Target System (NP-H36GS) Emulation board IE-789136-NS-EM1 Emulation probe NP-H36GS Flexible board NGS-30 75 mm 22 mm 22 mm Target system Remark NP-H36GS and NGS-30 are a products of Naito Densei Machida Mfg.Co., Ltd. User's Manual U14363EJ2V0UM 37 APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM Figure B-3. Distance Between In-Circuit Emulator and Conversion Adapter (NP-30MC) In-circuit emulator IE-78K0S-NS or IE-78K0S-NS-A Target system Emulation board IE-789136-NS-EM1 NP-30MC Head PWB 150 mm CN2 Emulation probe NP-30MC Conversion adapter YSPACK30BK, NSPACK30BK Remark NP-30MC is a product of Naito Densei Machida Mfg. Co., Ltd. YSPACK30BK and NSPACK30BK are products of TOKYO ELETECH CORPORATION. 38 User's Manual U14363EJ2V0UM APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM Figure B-4. Connection Condition of Target System (NP-30MC) Emulation board IE-789136-NS-EM1 Emulation probe NP-30MC NP-30MC tip board Guide pin YQGUIDE 13 mm Conversion adapter YSPACK30BK, NSPACK30BK 5 mm 15 mm 37 mm 20 mm 31 mm Target system Remark NP-30MC is a product of Naito Densei Machida Mfg. Co., Ltd. YSPACK30BK, NSPACK30BK, and YQGUIDE are products of TOKYO ELETECH CORPORATION. User's Manual U14363EJ2V0UM 39 [MEMO] 40 User's Manual U14363EJ2V0UM [MEMO] User's Manual U14363EJ2V0UM 41 [MEMO] 42 User's Manual U14363EJ2V0UM Facsimile Message From: Name Company Although NEC has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. Despite all the care and precautions we've taken, you may encounter problems in the documentation. Please complete this form whenever you'd like to report errors or suggest improvements to us. Tel. FAX Address Thank you for your kind support. North America Hong Kong, Philippines, Oceania NEC Electronics Inc. NEC Electronics Hong Kong Ltd. Corporate Communications Dept. Fax: +852-2886-9022/9044 Fax: +1-800-729-9288 +1-408-588-6130 Korea Europe NEC Electronics Hong Kong Ltd. NEC Electronics (Europe) GmbH Seoul Branch Market Communication Dept. Fax: +82-2-528-4411 Fax: +49-211-6503-274 South America NEC do Brasil S.A. Fax: +55-11-6462-6829 P.R. China NEC Electronics Shanghai, Ltd. Fax: +86-21-6841-1137 Taiwan NEC Electronics Taiwan Ltd. Fax: +886-2-2719-5951 Asian Nations except Philippines NEC Electronics Singapore Pte. Ltd. Fax: +65-250-3583 Japan NEC Semiconductor Technical Hotline Fax: +81- 44-435-9608 I would like to report the following error/make the following suggestion: Document title: Document number: Page number: If possible, please fax the referenced page or drawing. Document Rating Clarity Technical Accuracy Organization CS 02.3 Excellent Good Acceptable Poor |
Price & Availability of IE-789136-NS-EM1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |